Autel MaxiIM IM608 II
1. The operating system changes from Android 4.4 to Android 10.
2. Upgraded 8-core Qualcomm SDM660 8-core processor replacing the old Exynos T5260 6-core processor.
3. Doubled RAM and ROM: 4GB/128GB; SD card support up to 64GB (IM608 Pro supports max 32GB)
4. 16MP rear camera replaces the previous 8MP camera.
5. Optimized latest software version and more intuitive user interface.
Conclusion: Thanks to these upgrades, Autel IM608 II fixes ongoing latency issues, low response times, unstable network issues, and other issues that were common with the old IM508/IM608/IM608 Pro. Autel IM608 II not only provides a more intuitive navigation interface, but also improves the running and response speed by 5 times.
Newly Added Features of Autel IM608 II:
Autel IM608 II provides more options for quick vehicle identification, such as adapters), which can perform faster and more stable diagnosis on newer models of vehicles.
Added new features to Autel IM608 II that cannot be achieved with older models, such as: B. IMMO programming for BMW & Benz; Engine E/CU Read & Write provides wider vehicle coverage, supports reading and writing CAN protocol chips without password
Supports remote expert function.
Autel MaxiIM IM608 II
Autel IM608 II IMMO tool: the best of the best in the Autel MaxiIM series!
As an upgrade version of Autel IM608 Pro, Autel IM608 II covers 95% of vehicles (2000 later), and enables direct learning and matching of operational keys via OBD for 85% of vehicles, can read IMMO DTCs, perform IMMO data for the pro-programmed keys/chips, IMMO E/CU reset, customization, update, coding and more. Provides two modes for IMMO functions: smart mode and expert mode, allows users to choose based on different situations and
needs, thereby maximally improving work efficiency.
Smart Mode: Provides guided features with step-by-step instructions and all you need to do is follow the instructions and click "Yes" and everything you need will be completed. This mode is suitable for beginners or do-it-yourselfers.
Expert mode: Access to a function menu where each function is separated from each other. Experienced technicians can use this mode to run single functions instead of all functions to save time and improve work efficiency.
The supplied maxi programmer XP400 Pro can fully exploit its capabilities:
(1) Read transponder data (including Mercedes Benz infrared smart key) and generate exclusive keys.
(2) Read/write on-board EEPROM chip data and read/write MCU/ECU chip data.
(3) Read/write remote control transponder data and detect key frequency.
(4) Read PIN (All Keys Lost/Add Key);
(5) Distance Learning / Key Generation / Key Learning
(6) For VW/Audi 4th/5th Generation IMMO Key Learning; For VW MQB Key Learning via OBD; For VW/Audi/BMW Key Unlock
(7) For Benz 3rd Generation IMMO Add Key, All Key Lost via OBD; For Benz OE NEG Key Learning
(8) For BMW FEM/BDG Key Learning and Adaptation; For BMW CAS4/3/2 key learning; For BMW EWS3 Key Learning
(9) backup/restore IMMO data; IMMO E/CU reset / adaptation / refresh / coding
Autel MaxiIM IM608 Pro II
Autel IM608 II Key Programming Tool: Do more than you expected!
You cannot start your car without a programmed transponder key. Car key programming is an essential process that your key fob must go through in order for it to function and start the vehicle. To avoid compromised security, defective modules, broken vehicles and very expensive repairs, you need a professional tool to help you perform key exchange procedures correctly. Autel Professional Key Programming Tool Autel MaixIM IM608 II is a long-term good investment for auto locksmith, not only improve your work efficiency but also bring more business and profit. IM608 II is a good solution for:
Read/write transponder data
Read/write MC9S12 encryption chip
Read/write IC card
Read/write E/CU/MCU/EEPROM data
Read/write Mercedes infrared key
Read/Write IC chip keys on Hyundai and KIA
Detect remote frequency
Equipped with this, Autel XP400Pro enables programming of infrared keys for Mercedes vehicles and IC chip keys for newer models of Hyundai KIA vehicles, performs EEPROM data functions required for European vehicles, and supports reading/writing data of more than 3,000 chip types (incl . EEPROM, Motor ECU, MCU, IMMO ECU):
Over 170 kinds of odometer component reading functions
Over 180 kinds of immobilizer E/CU components
Over 40 engine E/CU component types
Over 2000 MCU component types
440+ EEPROM component types
Autel MaxiIM IM608 II: Advanced J2534 E/CU Coding and Programming Tool !
Autel IM608 II is equipped with the powerful MaxiFlash Elite J-2534 Pass-Thru Programmer and has the same E/CU programming and coding features as Autel MK908P II and MaxiSYS MS908S Pro II. Below is a brief introduction of these features :
Online & offline E/CU programming:
(1) program the data to a new IMMO module,
(2) repair the IMMO E/CU data loss,
(3) IMMO E/CU software version upgrade, etc.
Online programming only works for BMW and Benz specific vehicle models.
Offline programming requires OE-authorized programming software. Connect the MaxiFlash Elite J-2534 pass-through to the PC to perform reprogramming functions on any modern vehicle diagnostic bus.
ECU Coding Functions: Matching and coding newly replaced modules, changing preset module parameters, enabling functions hidden by manufacturer, OE setting customization and so on. The E/CU coding function allows you to re-code adaptive data for specific components after repairs or replacements to improve driving performance, fuel efficiency and reduce power loss.
Component Matching: Write adaptive data to match different onboard modules after replacement.
OE Setting Customization: Modify preset software parameters to reduce power loss, improve fuel efficiency, reduce component wear and so on.
Enable high-end features: e.g. B. Activation of the interior lighting, roof lighting, automatic folding and unfolding of the mirrors, daytime running lights, etc.
Disable functions you don't need: like disabling auto start/stop, locking seat belt warning beeps, injector hum beeps, etc.
Online E/CU coding:
Direct access to high-end vehicle repair OEM online coding data.
Compatible with BMW, for Benz, for Audi, for Porsche etc
Note: E/CU programming and coding functions are not universally compatible for all vehicles. The specific features also vary by car make, model and year. Please provide the VIN so we can check feature compatibility.
Autel IM608II
Autel MaxiIM IM608 II: 36+ Services and Special Features to Expand Your Business!
Autel Scanner MaxiIM IM608 II offers over 36 service functions including commonly used reset and maintenance functions that a DIY enthusiast or auto technician would need for daily car maintenance. Listed below are some of the most popular services:
Oil Reset: Reset the new engine oil life system calculation for an accurate indication of the next oil change.
EPB Reset: Reset the brake calipers, brake discs or pads after the electronic parking brake system has been repaired.
BMS Reset: Reset after battery replacement to clear the original battery low battery error information and protect the new battery.
IMMO / Key Programming: Block a lost vehicle key to protect the vehicle from theft and add the new key. (Only works on Asian cars that have inferior IMMO system
Injector Coding: Code a new injector to better identify injectors and accurately control fuel injection.
ABS Bleed: Perform to bleed the brake system to restore ABS brake sensitivity and maintain firm brake pedal.
SAS setting: erase memory of faulty steering angle sensor, reset steering angle sensor and turn off steering wheel warning light.
Throttle Relearn: Reset the throttle actuators to finely regulate throttle (or idle motor) operation, helping to keep your idle and acceleration smooth.
Headlight Adaptation: Initialize the adaptive headlight system
More can be done after maintenance/reset or component replacement: initial adjustment, auto-learning, re-learning, auto-detection. Like crankshaft sensor learning and etc.
Note: The above mentioned is only a small part of all supported services and more are not listed. Please also note that not all service and special functions are universally compatible. Please send us the VIN number and the features you need to check compatibility.
IM608II
Autel IM608 II 2023 Version: All system diagnostics and full bi-directional control function same as Autel Elite II!
In addition to its professional IMMO and key programming capability, Autel MaxiIM IM608 II is also a high-end general diagnostic tool that can access all available modules and systems to perform thorough OE level diagnostics and has full bi-directional control capabilities to accurately test different actuators to determine if repair or replacement is required. These functions are the same as Autel MaxiSYS Elite II, which can support 98% of mainstream US, Asian and European vehicles up to newer 2021, 2022 and 2023 models.
Language switching service & no IP restriction & :
Autel IM608 II is designed to cater to global users with different language backgrounds, so it offers different language options. The default language of this device is English and can be changed to German, French, Italian, Swedish, Portuguese, Spanish and many more.
